Marc Petitjean Day Light With Tool Rack, this light is extremely versatile, having a long flexible neck giving you maximum freedom around the vice head. The tool rack has several diameters for all the tools needed for Fly assembly. It also comes with dual voltage for worldwide use.Marc Petitjean Day Light With Tool Rack features:
- Switch (on/off) on the head lamp
- Cold LED daylight - 3W- 110 to 230 volts (EU/US standard)
- For stem 8mm up to 10mm (3/8")
- Contained in a soft travel case (600 g)
Note this does not include the vice, just the light & tool rack)
Tube Fly Holder-Vice Adaptor - Although only a simple piece of kit, this little adapter will make the job of tying tubes much less stressful. Fits into the jaws of a standard tying vice. The tapered collet allows good access to the tube unlike some other adapters on the market.
Peak LED Fly Tying Light is the best portable lighting solution we have found providing a full spectrum white light that won't skew the colour properties of the fly tying materials you are working with. The LED light source runs cool providing 120 degrees of lighting to illuminate your entire tying area with up to 300 lumens and with minimal power consumption. Even running the Peak LED Tying Light after a full day of tying you'll find the housing remains cool to the touch - No need to worry about burning your hand if you accidentally touch your light!The Peak LED Tying Light bracket mounts to any PEAK vise stem, PEAK's Accessory Shaft or any other 3/8" diameter vice stem and incorporates an integral tool holder. Use the 20" flexible neck to allow optimal positioning of the light, last but not least another great benefit is the Lights so lightweight in construction it can be easily transported.
Peak C CLAMP now you can mount your Peak vise onto anything from a banquet table to a picnic table. The Peak C Clamp clamping jaws ride on 2 precision guide pins keeping the jaw faces parallel. Unlike a typical clamp screw, there is no rotating clamp pad causing your vice to "walk" as it's clamped to the table or marring the finish. The rabbeted face engages the edge of your table so your vise won't rock. As one reviewer stated "You could press bearings with this clamp." Works with any 3/8" shaft and the Clamp will also accept Peaks Accessory Post.
Peak Tube Fly Vice Head available for PEAK vise owners who do not want to buy a second complete vise. The Peak Tube Fly Vise Head is easily changed using the Hex Key provided. The vice head comes with the two pins (1/32"and 1/16")Note: Pictured fly not included.
Peak Accessory Shaft a unique and very useful accessory providing a place to mount items such as a light etc. near your fly tying work area but not on your vise. Peak The Accessory Shaft is compatible with both PEAK's Pedestal Base Vise and C-Clamp Vice, the Accessory Shaft will accept any accessory designed to mount onto a 3/8" diameter shaft. (Note Picture: Accessories and Vises shown for illustration and are not included with the Accessory Shaft)
Peak Rotary Vice Midge Jaw undergo the same hardening and tempering process as the Peak highly acclaimed standard jaw. The Peak Rotary Vise Midge Jaw are specifically profiled to allow more access to tie on smaller hooks and are not recommended for extended use with hook wires larger than a #16 dry fly hook. Black oxide finish reduces glare in the immediate area of your hook.
Peak D Arm - Horizontal rotary handle to replace the vertical handle. Easily assembled (tool included), this rotating handle will "turbo-charge" your fly tying. The freely rotating shaft allows you to rotate your vise without having the handle spin in your fingers.
Peak Material Clip comes with 2 sizes of spring to grip a wide range of fly tying materials. PEAK's straight spring design works better than a conventional wrapped spring which results in the spring coils forming an inverted "V"; PEAK's straight spring leaves parallel coils holding your fly materials more securely. The PEAK Material Clip will fit any 1/4" Diameter shaft. Clips will rotate to any angle needed or completely out of the way and multiple Material Clips can be used in tandem.
Peak Tool Post Caddy, a useful and very popular Peak accessory to help you stay organized and increase your fly tying output. No more looking for lost tools hidden under your materials or that have rolled off on the floor. Hang your essential tools right next to your vise, out of the way for when you need them. The Peak Tool Post Caddy Fits any 3/8" shaft such as your PEAK Vise or PEAK Accessory Shaft. (Vise, Accessory Shaft, and tools shown for illustration and are not included with the Tool Post Caddy).
Peak Vice Travel Pouch, sewn in the USA, in Colorado, home of the Peak Vise. The Peak Vice Travel Pouch has a heavy duty outer shell of tough Cordura for years of use. The two padded interior compartments separate and protect your vise and accessories, holding any of PEAK's vices, Pedestal Base or C-Clamp.(Vise, Pedestal Base, and Bobbin Cradle Assembly shown are not included with pouch)
Peak Pick 'N' Brush, Peak's combo dubbing tool, the Ritt-Pick-N-Brush is almost a necessity on any fly tyers bench. It incorporates a nylon dubbing brush, bodkin needle and half hitch tool in one package. The nylon brush is gentler on thread and hackle than metal brushes. The Ritt Pick-N-Brush allows you to carry fewer tools for more functions.
PEAK Riser will work with the PEAK Pedestal Base or PEAK C-Clamp (in fact it is compatible with any base or clamp that fits a 3/8" diameter vise shaft) and will accept any vise having a 3/8" diameter shaft. The PEAK Riser allows you 1-3/4" additional height adjustment. Leaving the riser attached to your vise and disassembling it from the Pedestal Base will leave you with a flat base for easier transportation.
Marc Petitjean Tool Rack, perfect to store all your fly tying tools, always visible and accessible. Marc Petitjean Tool Rack is perfect for most fly tying vises, not just the Petitjean series, fits on Vice stems diameters; 8 mm to 10 mm (3/8 inch diameter).
The Marc Petitjean Tool Rack has 3 different sized grillings allowing for various tying tools (5 x 9 mm, 4 x 4.5 mm and 4 x 2.5 mm)
(Note the Marc Petitjean Tool Rack illustration shows example of the set up on the vice, you are ordering the rack only - no tools or vice)
Stonfo Tube Fly Tool turns your fly vice into a tube fly vice - this tool can be fixed in to any vice to tie tube flies easily. The Stonfo Tube Fly Tool features a vice adapter tool, and 2 stainless steel pins, 1.1mm & 1.5mm, to fit the vast majority of tubes. Also suitable for big sea lures. Stonfo Tube Fly Tool pack contains basic set up instructions.
Snowbee Integral Tube Fly Attachment designed for the Snowbee Waldron Vice, simply replaces the standard vice head, converting the vice to a precision Tube Fly model. The central tube pin locks in place with a small screw and compression is then applied to the tube by means of the reverse threaded 'Cone' head and locking collar. The cone head features a fine parallel tip, which allows the tube to be held in position with the silicone sleeve already in place, making it the perfect choice for professional tube-fly dressers. Both versions come with two different pin sizes to cater for different sized tubes.
Note picture shows Waldron Vice clamp with tube fly attachment for illustration only.
Snowbee Vice Sight Board & Bobbin Cradle, an ingenious double pivot and stem system supports both a sight board and bobbin cradle, allowing totally independent movement of each component. The sight board can be rotated around the vice jaws, allowing for left or right hand positioning, and the bobbin cradle through almost 360°, or can be folded away behind the head, when not required.
A unique cradle head features a traditional 'V' groove one end to drop a tying thread into, but also has a second groove fitted with 2 rubber 'O' rings. This allows thread to be locked in place, cut and dubbed, separate to the main bobbin thread.
Material Spring - An invaluable fly tying accessory. Simply wrap the spring around the vice near the jaws and use this material spring to hold delicate hackles, threads, tinsels, wires etc. etc. when you need an extra pair of hands.
Veniard Waste Bag - This is a very handy supplementary bit of kit, for all your waste bits, attaches to the vice stem and keeps the trimmings off the carpet.
Stonfo Magnifying Glass, specially designed for fitting on vices allowing to see clearly without distortions to any small details during the tying. It has a flexible arm fully adjustable to any position with a small attachment that permits an easy and stable locking on vise stems from 8 to 10 mm diameter and on accessories stems of 5 mm diameter.
Technical data: 2X magnification, lens dimensions 80 mm, length flexible arm 350 mm, weight 170 gr.
Picture illustration only showing vice connected, no vice included.
Stonfo Profile Plate STF542 - Swivel site board, double colour black and white for your fly tying. The Stonfo Profile Plate is equipped with a magnetic rest device that swivels 180° for a quick change of non- reflective colour. Fits vices with a stem 8-10 mm Ø.
Note: Pack contains 1 x Stonfo Profile Plate a magnetic rest device - Picture for illustration showing vice, bobbin holder etc. which is not included.
Stonfo Joint Block STF 626 clamps on to a fly tying vice allowing the positioning up to four accessories at the same time. The Stonfo Joint Block Fits on vice stems from 8 mm to 10 mm (3/8") and is supplied with 8 mm adaptor bush and allen key.
Note picture for illustration no vice included. Special Order - Available to dispatch circa 3 - 5 days after ordering.